How to Remove Magnesium Chloride From Trucks & Trailers: Winter Wash Guide
Quick answer: To remove magnesium chloride from a truck or trailer, start with a high-volume rinse of the undercarriage. Then foam on a low-pH Step 1 soap followed by a high-pH Step 2 soap to break down the road film the brine is trapped in. Finish with a thorough high-pressure rinse of the frame rails, suspension, wheel wells and every spot the spray kicked up into. Mag chloride dissolves in water, so the rinse is what actually carries it away. The soap's job is to break the grimy film holding it against the metal. Wash after every storm cycle, not just when the truck looks dirty.
If your trucks run Midwest, Mountain West or Northeast highways, you already know the white crust. What you may not know is that much of what's sprayed on winter roads today isn't rock salt. It's liquid brine, often made with magnesium chloride or calcium chloride. It sticks harder, stays wet longer and gets into places rock salt never reached. This guide covers how mag chloride differs from road salt and how to wash it off semis, trailers and pickups. It also covers what a truck wash soap can and can't do about it, because the honest answer matters when you're protecting equipment that costs six figures.
What is magnesium chloride, and why is it on my truck?
Magnesium chloride is one of the liquid chemicals highway departments use for anti-icing. They spray it on the pavement before and during a storm so snow and ice can't bond to the road. The Federal Highway Administration's Manual of Practice for an Effective Anti-icing Program lists magnesium chloride and calcium chloride alongside sodium chloride (road salt) as common liquid anti-icing chemicals. The chlorides work at lower temperatures than plain salt, which is exactly why states use them.

For your trucks, that means three problems rock salt didn't cause:
- It's a liquid. Tires and wind turn it into a mist that coats frame rails, crossmembers, air tanks, brake components, wiring and the back of every mud flap.
- It stays wet. Magnesium and calcium chloride pull moisture out of the air. As FleetOwner reported, magnesium chloride stays moist at relative humidity above roughly 27%. A surface that looks dry can still be wet with brine and still corroding.
- It creeps. Maintenance professionals in the same report said that once mag chloride wicks into a joint between two metals, it's very hard to get out. That's why seams, connectors and wiring take the worst of it.
Is mag chloride worse than road salt?
The research is genuinely mixed, and we'd rather tell you that than oversell it. Colorado DOT laboratory testing in the early 2000s did not find magnesium chloride consistently more corrosive than sodium chloride on every metal. In the same period, a 2002 American Trucking Associations Foundation survey found that 72% of Colorado trucking companies reported increased wear on their equipment after the state began using it, as reported by FleetOwner. The practical takeaway for fleets: because chloride brine stays wet and creeps into joints, treat it as at least as damaging as salt and wash more often.
The cost of skipping it is real. AAA's road de-icer and rust damage fact sheet estimated U.S. drivers spend about $3 billion a year repairing rust caused by salt and liquid de-icers. It calls out brake lines, fuel tanks and exhaust systems, and it recommends washing after every significant winter storm with extra attention to the undercarriage.
What truck wash soap can (and can't) do about mag chloride
A lot of products promise to "neutralize salt." Here's the plain chemistry, so you can set the right expectations for your drivers and your shop.
What a good 2-step wash does:
- Breaks down the traffic film. Brine dries into a grimy film mixed with road oil, diesel soot and dirt, and plain water often beads off that film without cutting it. A low-pH Step 1 like Touchless Pro 1 is built to attack mineral-based road film. A high-pH Step 2 like Total Brite 2 breaks down the grease and road grime that are left.
- Gets the chlorides into the rinse water. Magnesium and calcium chloride dissolve readily in water. Once the film is broken, a thorough rinse carries the dissolved brine off the truck.
- Balances the surface. In a 2-step system the alkaline Step 2 neutralizes the acidic Step 1, so you're not leaving low-pH chemistry behind on the vehicle.
What no soap does:
- "Neutralize" chloride itself. Chlorides aren't an acid or a base. They're removed by dissolving and rinsing, not by a chemical reaction. When we say our 2-step chemistry neutralizes, we mean the Step 2 soap neutralizes the pH of Step 1.
- Reach places water can't. Brine that has wicked deep into a connector, a lap joint or under a loose undercoating won't come out with a surface wash. That takes inspection and maintenance.
- Undo existing rust or act as a rust inhibitor. Our soaps clean. They aren't corrosion inhibitors, rust converters or undercoatings.
How to wash magnesium chloride off a semi truck or trailer: step by step

- Wash warm if you can. A heated bay is ideal. If you have to wash outdoors below freezing, keep the wash moving so nothing freezes on the surface. Dry door seals, locks and steps before the truck sits.
- Rinse the undercarriage first, and rinse a lot. Start with a high-volume rinse of the frame rails, crossmembers, suspension, fifth wheel, wheel wells and the back side of mud flaps. A low-profile tool like the Under Carriage Cleaner 2.0 (rated 1,500–4,000 PSI) reaches across the underside without crawling under the truck. FleetOwner's fleet washing coverage also warns that water re-activates dried de-icing chemicals and that spray direction matters. Aim to flush brine off and out of components, not deeper into connectors and seams.
- Apply Step 1 (low pH) from the bottom up. Bottom-up application gives even coverage and keeps runs from streaking. Keep dwell short (about a minute, depending on the weather) and never let the product dry, especially on polished aluminum.
- Apply Step 2 (high pH) directly over Step 1. The two steps work together, so foam Step 2 over the top before Step 1 dries.
- Rinse thoroughly, and then rinse again underneath. Rinse until no foam remains anywhere: cab, frame, tanks, wheels, trailer undercarriage and landing gear. The underside is where the brine lives, so it gets the most water.
- Take care of the aluminum. Winter road film dulls aluminum fast. For unpolished aluminum trailers, truck bodies and wheels, Alum-Brite is an acid brightener that cuts oxidation and road film. It contains hydrofluoric and sulfuric acid, so it is not for polished aluminum, chrome or glass. Always neutralize it with a high-pH Step 2 and follow the SDS. For polished aluminum, stick with a polish-safe 2-step like Touchless Pro 1 and Total Brite 2.
- Add protection on painted surfaces (optional). A foam-on, rinse-off protectant like Wax Replacement leaves a rain-repellent finish that helps water sheet off paint between washes.
How often should you wash a truck in winter?
AAA's guidance is to wash after every significant winter storm, paying particular attention to the undercarriage. For fleets running treated highways, a good working rule is to wash after every storm cycle, once the roads have been treated, rather than on a fixed calendar. Brine is still on the road for days after the snow stops. Our fleet wash frequency guide and road brine and calcium chloride guide go deeper on scheduling.
Which Image Wash chemicals to use for winter washing
| Your operation | What to run | Why |
|---|---|---|
| Owner-operators and pickups (foam cannon) | Touchless 1 & 2 (1 or 5 gallons of each) | 2-step touchless soap that breaks down road film, bugs and winter salt. Polish-safe when used as directed. |
| Fleets and wash bays with a soap injector | Touchless Pro 1 + Total Brite 2 (55 gal drum or 275 gal tote) | Concentrates: pre-mix 1 part soap to 1.5 parts water, then draw through your injector. Both are polish-safe. |
| Fleets that don't want to pre-mix | Touchless Pro 100 + Total Brite 200 | Ready to use. Draw straight from the drum, no pre-mix needed. Polish-safe. |
| Dump trucks, ag and off-road equipment | Single Step | 1-step alkaline soap for mud, clay and heavy soils. Not polish-safe, so keep it off polished aluminum. |
| Unpolished aluminum trailers and bodies | Aluminum brighteners | Acid brighteners for oxidized, road-filmed unpolished aluminum. Follow with a high-pH Step 2. |
Not sure what metering tip your pressure washer needs? Plug your PSI and GPM into our Soap System Calculator. It shows the pre-mix and tip for every Image Wash chemical.
Don't let your chemicals freeze
This one gets missed every winter. The Safety Data Sheets for our wash chemicals say to protect them from freezing. Store drums, totes and pails inside a heated space, not in an unheated trailer or on the wash pad overnight. If you buy in bulk, plan ahead. Drums and totes ship by LTL truck freight, so order before you're down to your last few gallons. See how drum and tote freight works, and get a live freight estimate on any 55 gallon drum or 275 gallon tote product page.
Mind your wash water
Winter rinse water carries dissolved chlorides plus everything else that came off the truck. Rules for where wash water can go vary by city and state. Check with your local wastewater authority, and see the EPA's NPDES permit program for the federal framework. Our wastewater discharge permit guide walks through the basics for wash operators.
Frequently asked questions
Does magnesium chloride wash off with water?
Yes, magnesium chloride dissolves in water, so water is ultimately what removes it. The catch is that brine dries into a film mixed with road oil and grime that a quick rinse often leaves behind, and it can stay damp in seams and joints. A 2-step wash breaks that film so a thorough rinse can carry the chloride away.
What is the best soap for removing mag chloride and road salt from trucks?
A 2-step touchless system: a low-pH (acidic) Step 1 followed by a high-pH (alkaline) Step 2, then a thorough rinse. For pickups and owner-operators, Touchless 1 & 2 is the easy option. For fleets with a soap injector, Touchless Pro 1 and Total Brite 2 in drums or totes keep cost per wash down.
Does any truck wash soap neutralize magnesium chloride?
No. Chlorides are removed by dissolving and rinsing, not by being neutralized. Be wary of any product that claims otherwise. In a 2-step wash, "neutralizing" refers to the Step 2 soap neutralizing the pH of Step 1.
Is magnesium chloride more corrosive than road salt?
Lab results are mixed. Some state DOT testing did not find it consistently more corrosive than sodium chloride on every metal. But because it stays wet longer and wicks into joints, many fleets report more wear where it's used. Treat it as at least as damaging as road salt and wash more often.
How often should I wash my semi in winter?
After every significant storm cycle once roads have been treated, with extra attention to the undercarriage. AAA also recommends washing after every significant winter storm.
Can a touchless wash get mag chloride out of wiring and seams?
Not entirely. A wash removes what water can reach. Brine that has wicked into connectors, lap joints or under loose undercoating needs inspection and maintenance, which is one more reason to wash often, before it has time to creep in.
Can truck wash chemicals freeze?
Yes. The SDS for our wash chemicals say to protect them from freezing. Store drums, totes and pails in a heated space during winter.
Nov 02, 2026