Conquer 1 is a mint‑scented low pH detergent engineered as the first step in a two‑step commercial vehicle wash system for fleets, wash bays, and industrial equipment. It quickly attacks road film, grease, and mineral buildup on tractors, trailers, buses, and heavy machinery while remaining polish‑safe when used as directed. Designed for use through pressure washers or injection systems, it delivers consistent, high‑volume cleaning power for serious wash operations.
What Makes Conquer 1 Different
Most acidic detergents are either too aggressive on polished aluminum and sensitive finishes or too weak to handle real‑world commercial grime. Conquer 1 is formulated in a low pH range of about 1.0–2.0 to bite into tough soils while staying polish‑safe when properly applied and rinsed.
Used as the “Step 1” low pH detergent in a two‑step system, it pre‑treats road film and contamination so your alkaline “Step 2” soap can neutralize and fully remove what’s been loosened. This chemistry‑driven approach reduces or eliminates the need for manual brushing on most fleet vehicles, saving time and labor across every shift.
Recommended Use Routine
- Set up Conquer 1 on your soap injection system or proportioner according to your target dilution and equipment manufacturer guidelines.
- Starting at the bottom of the vehicle and working upward, apply Conquer 1 evenly to trucks, trailers, buses, or equipment, avoiding product drying on the surface.
- Allow a short dwell time (1 minute dwell times, weather‑dependent); never let the product dry, especially on polished aluminum and sensitive metals.
- Follow immediately with your chosen Step 2 high pH detergent, such as Total Brite 200, foamed directly over Conquer 1 to neutralize and lift remaining soils.
- Rinse thoroughly with high‑pressure water from bottom to top until all detergents and residues are removed.
- Inspect high‑visibility and polished areas and spot‑treat if needed; repeat the two‑step process only where necessary.
- To avoid repeated applications, lightly brush heavily soiled areas.
Equipment & Setup Recommendations
Conquer 1 is built for professional wash environments and performs best using a pre-configured Image Wash Products downstream injection system.
- Centralized soap injector systems for multi‑bay truck washes and fleet facilities.
- High‑pressure wash systems and arches in automatic truck and bus wash tunnels.
- Mobile fleet washing rigs set up for two‑step washing with separate low pH and high pH lines.
- Chemical‑resistant hoses, pumps, and fittings rated for low pH detergents.
- Proper PPE (gloves, eye protection, and protective clothing) for technicians handling concentrated product.
Why You Need Conquer 1
- Delivers low pH cleaning power (approx. 1.0–2.0) that attacks road film, oxidation, and mineral deposits on commercial vehicles.
- Helps reduce or eliminate brushing on most fleet surfaces when paired with a strong Step 2 alkaline detergent.
- Polish‑safe acidic formula when used as directed, designed for use around polished aluminum, chrome, and stainless in commercial wash environments.
- Formulated specifically for trucks, buses, heavy equipment, and industrial machinery—not a repurposed consumer car soap.
- Ideal for high‑volume fleet maintenance, dedicated truck washes, and industrial wash bays that need consistent, repeatable results.
- Works through pressure washers, arches, and injection systems, integrating seamlessly into automated or semi‑automated wash setups.
- Mint‑scented green formula improves the wash bay experience for operators and thick foam makes visual coverage easy to see.
- Pairs perfectly with Total Brite 200 and other Image Wash step two soaps for a complete, chemistry‑balanced two‑step system.
Conquer 1 at a glance
| Chemistry | Mint-scented low pH (acidic) Step 1, pH about 1.0–2.0, organic acid blend |
|---|---|
| Pair with | A high pH Step 2 such as Total Brite 200 |
| Polish-safe | Yes, when used as directed |
| Soap injector setup | Use straight. Draw directly from the container. |
| Final strength at the injector | 20:1 |
| Shipping class | Not regulated as a hazardous material for U.S. ground transport (SDS Section 14). |
| Safety Data Sheet | Download the Conquer 1 SDS (PDF) |
Injector setup and strength come from our Soap System Calculator. Enter your pressure washer's PSI and GPM there to get the right metering tip.
Use it on
- Road film, grease and mineral buildup on tractors, trailers, buses and heavy machinery
- High-volume wash bays with injection systems or proportioners
Keep it off / avoid
- Letting it dry, especially on polished aluminum and sensitive metals
- Long dwell times. About 1 minute, depending on the weather.
- Using it without a high pH Step 2
Conquer 1 FAQs
How long should Conquer 1 dwell?
About 1 minute, depending on the weather. Never let it dry.
What do I pair it with?
Foam a high pH Step 2 like Total Brite 200 directly over Conquer 1, then rinse from the bottom up until all residue is gone.
Is Conquer 1 polish-safe?
Yes, when properly applied and rinsed.
How drum & tote freight works
- Ships by LTL truck freight from Michigan. 55 gallon drums and 275 gallon totes go out on a freight truck, not by parcel.
- Get a live estimate on this page. In the freight estimator, choose a commercial address with a dock or forklift, a residential address or no dock (liftgate needed), or pickup at your local freight terminal. Then enter your ZIP code and state.
- Your estimate is saved with your order. When you add to cart, the quote is added to your order notes. Estimates aren’t final, and final freight charges may vary.
- Hazmat status: Not regulated as a hazardous material for U.S. ground transport (SDS Section 14).
- Order the right chemistry the first time. We don’t reimburse shipping costs on 5 gallon quantities and larger. If you’re not sure what fits your operation, call us at 616.777.7175 before you order.
- Outside the lower 48 states? Call us for a freight quote.
